Regulatory Compliance and Reporting

Compliance with laws and standards in industrial facilities is not only a necessity, but also the foundation of operational continuity and financial stability. At SWL, we guide you through the complex and constantly evolving labyrinth of regulations and certify that your facility meets all legal requirements.

Basic Legislation and Standards in Our Scope of Expertise:

• Regulation on the Protection of Buildings from Fire
• Occupational Health and Safety Law No. 6331 and related regulations
• TS 12845 and related EN standards (e.g. Sprinkler Systems)
• sector-specific regulations (SEVESO, ATEX, etc.)
• Special specifications of local fire departments

National Expertise, Global Perspective

We combine this deep understanding of local regulations with our expertise in international standards such as NFPA, ISO, and EN 10000. This holistic approach ensures your facility not only meets Turkish legal requirements but also is protected by international best practices.

Technical Risk Analysis and Modeling

Fire Risk Assessment: (Service No: FSR.1.1)

• Life Safety and Evacuation Analysis (NFPA 101): Based on the internationally accepted NFPA 101 Life Safety Code® standard, we evaluate the suitability of evacuation routes and life safety performance according to your facility’s architectural structure and human load.
• Thermographic Risk Mapping (ISO 18436-7): We proactively identify overheating points that could lead to electrical or mechanical failures using thermal imaging technology in accordance with the principles of the ISO 18436-7 standard.
• Performance-Based Fire Engineering (ISO 16733-1): We create numerical risk metrics for fire scenarios specific to your facility using modern fire engineering standards such as ISO 16733-1, providing a scientific basis for your investment and precaution decisions.

Electrical and Chemical Risk Analysis: (Service No: FSR.1.2)

• Arc Flash Hazard Analysis (NFPA 70E, IEEE 1584): By analyzing potential arc flash hazards in electrical panels according to NFPA 70E and IEEE 1584 standards, we determine the Personal Protective Equipment (PPE) levels and safety limits required for personnel to work safely.
• Process Hazard Analysis (PHA) and Exothermic Reaction Safety: We analyze chemical process hazards, such as runaway exothermic reactions, using internationally accepted Process Safety Management (PSM – ISO 31000 Risk Management) methodologies and strengthen your operational safety barriers.
• Explosive Atmosphere Risk Assessment (ATEX & EN 60079): In areas where flammable dust, gas and vapors are present, we perform hazardous area (Zone) classification and equipment conformity assessment in accordance with EN 60079 series standards.
• Electrostatic Discharge Risk Analysis (NFPA 77): In areas where flammable and explosive materials are present, we analyze the risks of static electricity accumulation and discharge under the guidance of NFPA 77 and determine grounding and control measures.

System Audit and Performance Tests

Security in industrial facilities is achieved not only by the existence of installed systems, but also by their ability to deliver the expected performance at critical moments. At SWL, we test the performance and integrity of your security systems using the most advanced technologies and international standards, providing you with true assurance.

Proactive Risk Detection with High-Tech Thermal Imaging:

Our thermal imaging service allows you to proactively detect potential faults and fire risks before they arise.

• Our Technical Capability: We perform precise measurements and real-time anomaly detection even in the most difficult and hazardous areas with wearable “hands-free” and ATEX certified intrinsically safe devices.
• Our Application Areas: Electrical Panels, Mechanical Equipment, Process Safety

Fire Detection and Alarm Systems Performance Tests:

These tests ensure that your alarm system will respond accurately and in a timely manner in a real emergency, not just on paper.

• EN 54 Compliance Audit: We verify the legal and technical basis of your system.
• Detector Sensitivity Test (Obscuration): We prevent false alarms and detection delays.
• Addressable Loop Impedance Measurement: We analyze the uninterruptibility of system communication.
• Alarm Verification Time Test: We measure the system’s response time in a real fire scenario.
• Cross-Zone Configuration Evaluation: We test scenario logic that will prevent erroneous extinguishing discharges.

Active Extinguishing Systems Performance and Integrity Tests:

We confirm that your extinguishing system can discharge the required agent (water, foam, gas) in the correct amount, pressure and concentration in case of fire.

• Sprinkler and Hydraulic Calculation Verification: We confirm that the system can provide the water/foam flow rate at the time of design.
• Fire Pump Performance Tests: We verify that your pump group can produce the required pressure and flow in the event of a fire.
• Assessment According to FM Global Standards: We analyze and report your facility’s compliance with international insurance standards.
• Foam Concentration Tests: We accompany and report the extinguishing effectiveness of the foam by ensuring the correct mixing ratio.
• Gas Extinguishing Room Integrity Test (Room Integrity): We verify that the extinguishing gas will remain in the location at the targeted concentration and duration by accompanying the tests.

Structural Fire Safety Assessment

While active suppression systems are a facility’s first line of defense, Structural Fire Safety (Passive Protection) is the fundamental insurance policy that slows the spread of fire and smoke, provides vital time for safe evacuation, and prevents structural collapse. Our services in this area aim to maximize this critical insurance for your facility.

Passive Fire Protection:

To limit the destructive effect of fire and control it within the compartment where it broke out, we carry out the following assessments:

• Verification of Fire Resistance: We calculate the fire resistance duration (R30-R120) of your structural elements (columns, beams, floors) and confirm their compliance with international standards.
• Inspection of Compartment Integrity: We check the integrity and sealing of compartment elements such as fire walls and floors that confine the fire to the area where it broke out.
• Penetration Sealing Tests: We verify the performance of firestop materials used in weak points such as installation and cable penetrations by accompanying the sealing tests.
• Fire Doors and Walls Certification Audit: We audit the certifications and installation conformity of all passive protection elements used.
• Smoke Control and Evacuation Systems Analysis: We analyze and report whether the systems that prevent or evacuate smoke spread (pressurization, smoke exhaust) operate effectively and in accordance with their engineering designs.

Escape Route Optimization:

In an emergency where safe evacuation is measured in seconds, the design and functionality of escape routes is vital.

• Evacuation Route Bottleneck Analysis: By modeling escape scenarios, we identify potential bottlenecks that could slow down the flow of people and offer practical solutions.
• Emergency Lighting Level (LUX) Measurements: We verify by measuring on site that emergency lighting levels along the entire escape route meet the relevant EN standards.
• Emergency Guidance Systems Assessment: We analyze the location, visibility and clarity of exit signs and report improvements that will facilitate the evacuation process.